Problems of oyster mushroom blocks

Problems of substrate colonization by mycelium

Substrate overgrowth defects occur for the following reasons:

  • heat treatment violations herbal raw material (straw, sunflower husk, hay),
  •  use of low-quality grain spawn (mycelium),
  •  lack of a clean zone,
  •  failure to comply with the conditions of the incubation period.

Dear readers of the site "Veshenka expert"! Gradually I will translate all the articles. But, while the links lead to Russian-language posts. Use google translate to read.

If the mycelium grows poorly and spots of non-growth form, do not rush to blame the grain spawn seller.
Uneven fouling of mushroom blocks is possible for many reasons.

For example, low temperature in the incubator (14-17 degrees) affects the rate of hyphae germination in the substrate mass. While the hyphae slowly grow, bacteria, which are quite comfortable at this temperature, actively multiply in the space between the film and the substrate, where moisture collects. Because of this, dark areas appear in the block.

Read how to properly incubate.
Or, you have incorrectly heat-treated raw materials.

Consider the main types of defects and how to eliminate them.

The content of the article
  1. Spots on an oyster mushroom block
  2. Mold on mushroom substrate
    - Green mold - trichoderma. 
    - Black mold on mycelium
    - Orange mold - Neurospora
    - Mukor - black hair on an oyster mushroom block
  3. Yellow mass in the perforation of an oyster mushroom block - slime mold

Spots on an oyster mushroom block

Spots are of three types:
- white,
- yellow or orange,
- dark.

White spots

They are isolated roundness, formed in the early stages of incubation and are clearly visible against a dark background of not yet overgrown husks. Sometimes noticeable even on the second or third day of incubation.

white spots

Such spots are formed around the caryopsis with mycelium. Most likely, these are hyphae of oyster mushroom mycelium, which has grown like a cobweb. Why some gifs behave this way, I cannot explain.

But, I know for sure - this does not characterize the grain spawn in any way - either for good or for bad.

If the raw material is processed with high quality, these spots do not affect the overgrowth process.

On the 6-7th day of incubation, when all the husks or straw turn white, they intertwine with the rest of the hyphae and do not stand out. The yield of the batch also does not depend on whether there were such spots at the beginning of overgrowth or not.

Such spots are not at all like stroma, a dense white crust, which is described here.

Yellow or orange spots

orange spotsSometimes under the film we see small spots of yellow, redheads or brown liquid. If these spots are almost transparent and have a pleasant smell, then the color appears due to staining with pigments from husks, straw or hay.

They are not dangerous and often disappear during fruiting.

But more often there are orange or yellow spots of non-growth on oyster mushroom blocks that are affected by bacteria.

Such packages have an unpleasant smell - sour, less often alcohol or ammonia. Such a spot looks like a yellow gelatinous formation or like a dark piece of straw or husk.

This is a sign of waterlogged substrate.

On a waterlogged substrate, yellow oyster mushrooms grow, often with a curly or wavy hat.

yellow jelly in oyster mushroom block
yellow spot and yellow oyster mushroom

If the substrate is too wet, the primordia will turn brown and sticky. If you squeeze them with your hand, drops of water appear.

The second reason why the mushroom block often turns yellow is an attempt to cool the blocks sharply during incubation.

If in this case green spots of mold do not form, then we see yellow spots where mycelium does not grow.

To avoid the formation of yellow spots, you need to make a substrate of optimal humidity (68-69%) and observe the microclimate parameters in the incubator. More about it.

Dark spots

dark spots on the substrateAs the bag grows, a clear boundary is formed between the white hyphae of the mycelium and the compost.

Or it happens that the colonization of the substrate (compost) by mycelium proceeds normally, it turns white, and then stops growing and darkens.

What prevents oyster mushroom mycelium from developing freely in the territory of the dark spot? Microorganisms to which the conditions in the spots are more suitable.

Such areas appear due to one of four reasons, or a combination of them:

  1. Uneven heating of the substrate in the container. For example, the top bags are not fully submerged into water or come into contact with a cold container wall.
  2.  Waterlogging of the substrate.
  3. Use of one water for heat treatment of several batches of husks or straw.
  4. If you do not wash the heat treatment container.
    Some mushroom growers think that the liquid left in the tank after draining the water will be heated during the next heat treatment and all the bacteria in it will die. Unfortunately, the opposite happens - the most resistant microorganisms survive and give new, heat-resistant strains, which then infect the entire batch, giving 100% spoilage.

Sometimes small larvae appear under the polyethylene in the area of ​​​​the dark spot (see photo here). It was they who ate the mycelium. Infected bags must be immediately removed away from the growing chamber, and the incubator should be treated with insecticides.

Don't forget about protective equipment!

Why does oyster mushroom mycelium not colonize the substrate

Mold on mushroom substrate

This is the most common type of defect (flaw).

This most often occurs during heat treatment of raw materials with hot water (hydrothermal method) and improper xerothermy (when dry raw materials are treated with steam).

It is difficult to distinguish oyster mushroom mycelium from mold in the early stages of growth, as most molds have the same white hyphae.
And only mold spores of different colors. It takes from 3 to 7 days for the spores to mature, and then you can see whose mycelium it is.

Green mold - trichoderma

Green mold trichodermaMost often, various types of trichoderma settle in the overgrown substrate, its spores are green in color: from olive to gray-green.

If the speck of mold is small, then the oyster mushroom hyphae eat it up, and fruiting subsequently proceeds normally. Large spots of mold, on the contrary, progress and inhibit the development of oyster mushrooms.

Many people are surprised that the mushroom block turned green on the 12th or even 15th day, and before that it was white.

In fact, the mold was in the raw materials from the very beginning.

But it was not visible, since the trichoderma hyphae are white, with a grayish tint. And when the mycelium of Trichoderma matured, we saw green clusters of its spores.

Since green mold annoys mushroom growers most often, I wrote a separate article about it.

Read: How to get rid of green mold

Black mold on mycelium

Black mold reproduces much less frequently than green mold. Most often, these are various types of mucor. But, you don't have to know exactly what type of black mold is in the block.

You can get rid of it in the same way as green mold

As a rule, black mold develops on poor quality raw materials. If rain falls on the straw or husk during storage, its moisture content rises. Mold spores germinate and multiply.

Sometimes there are so many of them that standard heat treatment of raw materials cannot kill a significant part of these spores. Even if you increase the temperature and processing time, it will not help.

The best option is to buy dry, clean raw materials and store them in a dry place.

Below I describe another type of black mold, popularly called "black hair"

Orange mold - Neurospora

Neurospora

This mold needs to be distinguished from Slime mold - this is the organism that I will talk about next.

If you find an orange substance in a bag, especially if it goes into a slot, seal the perforation with tape and take this block away from the enterprise.

Release it from the film, bury it, and burn the polyethylene. Be sure to treat the room with chemicals such as Armex, Virocid.

If there are already overgrown batches in it, take them out to the growing chamber. You may not want to carry freshly made blocks during the disinfection, but try not to get the drug on them.

Do not wait until the incubator is free - you risk losing everything that is there.

Neurospora reproduces very quickly, it can infect the entire incubator in a matter of days.

Neurospora is a soil fungus.

Infection of sunflower husks occurs if the stubble of cereal plants was burned on the field before sunflower sowing, spores also get into the straw.

Pink spot in oyster mushroom substrateNeurospore is a rather rare type of mold for mushroom growers - it is also called "red bread mold".

Its spores are orange-red or pinkish in color.

But if the spot is pure pink, it is probably another fungus, from the genus Fusarium. It infects the stalks of cereal crops, and more often appears in the straw raw materials with insufficient heat treatment.

With hydrothermia, it appears if the straw is not soaked, but immediately poured with hot water.

Mukor - black hair on an oyster mushroom block

On many old farms and poultry houses, even if the buildings have been abandoned for many years, specific pathogenic microflora persists. Most often, spores of various mold fungi.

Mukor - black hair on an oyster mushroom blockAmong them is the species of mucoraceae - Spinellus fusiger. This mold appears in a slot and looks like long black threads with black sporangia balls.

What do we have to do?

  • if your incubator is located in such a building, or it is very close to your territory - before starting work, find a team that will professionally disinfect with fungicides. In extreme cases, do it yourself, observing all precautions.
  • do not deviate from the technology of heat treatment of the raw materials; carry out sanitation; set the ventilation correctly, as high air speed contributes to the spread of this mold.
  • If the mushroom block is well overgrown, and such black hair sticks out only from a few slots, cover them with a plastic bag, like a cap. Then, break the hair sticking out inside the bag and tie up the bag so that the spores do not spread indoors. And seal these slots with tape.
  • If the mycelium is overgrown with stains and the mold has spread inside under the film, immediately seal all the slots with tape and take this batch away from the enterprise. Remove all blocks from the incubator and treat the room with any disinfectant that has a sporicidal effect or Topsin-M fungicide.

Read my article "How to deal with mold when growing oyster mushrooms"

Yellow mass in the perforation of an oyster mushroom block - slime mold

Slime moldSometimes when growing oyster mushrooms, you can meet living creatures of Myxogastria. They look a little like both mold and fungus. You can read about them on Wikipedia, the article is called "Slime mold".

Most often they settle in greenhouses and in adjacent territories. When dry, it resembles withered polyurethane foam. When there is a lot of moisture in the air, it looks like yellow mold or grows in a slimy bunch.

This yellow slime has pseudopods that travel through the growing chamber at a speed of 1 to 2 centimeters per hour.
Slime mold is almost never found in the incubator. But the mushroom growers who sent this photo saw it in the slot of the overgrown block.

In this case, a complete disinfection of the room is necessary.

If it is impossible to take out all the blocks from the incubator, it is necessary to disinfect the walls, floor, empty racks, trying not to get on the perforations in the blocks. The room is disinfected with an antifungal drug or hydrogen peroxide 5%, or a solution of any drug containing peracetic acid.

©  All articles on the site are copyrighted, posting on third-party resources is permitted only with the permission of the author.

Contacts for PAID consultations -

e-mail: veshenka.expert@gmail.com

WhatsApp: +380503960696 Don't call!

Send me a text message with a brief summary of your question - I will respond as soon as I can.

magnifiercrossmenu